Fortinet Network Card ASM CE4 User Manual

LED  
State  
Blue  
Description  
Ejection latch open. The module is ready for removal.  
QuickStart Guide  
HS  
FortiGate ASM-CE4  
Flashing  
Ejection latch opened during system operation.  
LED currently not in use.  
OOS  
PWR  
OT  
Green  
Off  
The module is properly inserted in the FortiGate unit.  
The module is not receiving power from the FortiGate unit.  
LED currently not in use.  
RST  
HS  
OOS  
PWR  
Green  
The correct cable is in use and the connected equipment has power.  
Port 1 to 4  
Left LED  
OT  
Flashing Green Network traffic at 100 Mbps. Flashing with the right LED, connection  
at 1000 Mbps.  
1
2
3
4
Amber  
Off  
The correct cable is in use and the connected equipment has power.  
Port 1 to 4  
Right LED  
Network traffic at 10 Mbps. Flashing with the left LED, connection at  
1000 Mbps.  
ASM-CE4  
Visit these links for more information and documentation for your Fortinet product.  
© Copyright 2008 Fortinet Incorporated. All rights reserved.  
Technical Documentation - http://docs.forticare.com  
Fortinet Knowledge Center - http://kc.forticare.com  
Fortinet Technical Support - http://support.fortinet.com  
Products mentioned in this document are trademarks or registered trade-  
marks of their respective holders.  
Regulatory Compliance  
FCC Class A Part 15 CSA/CUS  
01-30000-86935-20081215  
15 December 2008  
Package Contents  
Connector  
Type  
Speed  
Protocol Description  
Ports 1 to 4  
RJ-45  
10/100/1000 Base-T  
Ethernet Copper network connections.  
QuickStart Guide  
RST  
HS  
OOS  
PWR  
OT  
RST  
HS  
OOS  
PWR  
OT  
1
2
3
4
1
2
3
4
ASM-CE4  
ASM-CE4  
Copyright 2008 Fortinet Incorporated. All rights reserved.  
Trademarks  
Installing the AMC Module  
It is important to carefully seat the FortiGate ASM CE4 module all the way into the chassis.  
Only then will the FortiGate ASM CE4 module power-on.  
ASM CE4 module ports  
SWx/1  
IP:  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
SWx/3  
SWx/4  
IP:  
____.____.____.____  
____.____.____.____  
____.____.____.____  
____.____.____.____  
Netmask:  
IP:  
Netmask:  
IP:  
To complete this procedure, you need:  
SWx/2  
• A FortiGate ASM CE4 module  
Netmask:  
Netmask:  
• A FortiGate chassis with an empty AMC single-width (SW) opening.  
To avoid any electrostatic discharge, install in a static free area.  
Removing the AMC module  
FortiGate ASM CE4 modules are not hot swappable. The procedure for inserting the  
FortiGate ASM CE4 module into a FortiGate chassis slot requires the FortiGate unit to be  
powered off.  
Should you need to remove the ASM CE4, shut down the FortiGate unit using proper shut  
down procedures.  
To remove the ASM CE4 module  
To avoid any electrostatic discharge (ESD) when handling FortiGate ASM CE4 modules,  
install in a static free area.  
1. Ensure the FortiGate unit is powered off before proceeding.  
To insert a FortiGate ASM CE4 module into a FortiGate chassis  
2. To avoid any electrostatic discharge (ESD) when handling FortiGate ASM CE4 modules,  
install in a static free area.  
1. Ensure the FortiGate unit is powered off before proceeding.  
2. Remove the panel block on the FortiGate unit using the hot swap latch.  
3. Pull the latch on the ASM CE4 module to the extended position.  
3. Pull the hot swap latch on the right-hand side of the module to the extended position to  
unlock the module from the FortiGate unit.  
4. Gently pull the hot swap latch to remove the module.  
4. Insert the FortiGate ASM CE4 module into the empty slot in the chassis. Ensure the  
Fortinet logo is right-side up. It should be on the upper-right corner of the module.  
5. Carefully guide the module into the chassis.  
6. Insert the module by applying moderate force to the front faceplate near the upper edge  
to slide the module into the slot.  
The module should glide smoothly into the chassis. If you encounter any resistance  
while sliding the module in, the module could be aligned incorrectly. Pull the module  
back out and try inserting it again.  
7. Press the hot swap latch to lock in the module.  
8. Power on the FortiGate unit. The hot swap (HS) LED turns on and then begins flashing.  
Configuring  
Configure the ports on the ASM-CE4 as you would any other ports on the FortiGate unit. For  
more information on configuring ports, see the FortiGate Administration Guide.  
Using the Command Line Interface (CLI) use the following commands:  
config system interface  
edit <port_number>  
Using the web-based manager, go to System > Network > Interface to configure the IP  
address and netmask of the ports. The module ports are indicated as SWx/n, where n is the  
port number.  
set ip <ip_address>  
set netmask <netmask>  
set allowaccess {http | https | ssh | telnet | ping}  
end  
 

Conair Styling Iron CS41CS User Manual
Cornelius Beverage Dispenser R 404A REFRIGERANT User Manual
Craftsman Snow Blower 486244283 User Manual
Crown Audio Microphone PZM 11LLWR User Manual
Electro Voice Microphone N D868 User Manual
Escient Stereo Receiver AVX User Manual
EV Rider Speaker EVF 1152S 94 User Manual
Extron electronic Network Card IPA T RLY4 User Manual
Generac Power Systems Portable Generator 91355 User Manual
Global Machinery Company Grinder BG612HPL User Manual